#!/bin/sh
#
# board specific defaults
#------------------------------------------------------------------------------

#
# Summary:
#   Flight Core can be used on many airframes, but is meant to be paired with
#   VOXL (either through a cable or in the combo board flavor).  For this reason
#   this script has a bit more Logic (aka Bobby Tarantino) than normal.
#
# Flight Core Version Information:
#   V106 - Flight Core Stand Alone configuration
#   V110 - Flight Core VOXL-Flight configuration
#

#
# Common settings across Flight Core configurations
#

# Disable safety switch by default (pull high to 3.3V to enable)
#  V106 - J13 pin 5
#  V110 - J1011 pin 5
param set-default CBRK_IO_SAFETY 22027

#
# Stand Alone configuration
#
if ver hwtypecmp V106
then
	echo "Configuring Flight Core - V106"

	#
	# In Flight Core, J1 can be setup to be used as a serial port for TELEM2
	# and connected to VOXL via cables.  We'll configure this out of the box.
	# The user can later change this if they want, as these are configurable
	# and not necessarily required to be used with VOXL.
	#
	if [ $AUTOCNF = no ]
	then
		if param compare MAV_1_CONFIG 0
		then
			echo "V106 - Defualt configuration TELEM2 on /dev/ttyS4 at 921600 in Normal Mode"
			param set-default MAV_1_CONFIG 102 # TELEM2
			param set-default MAV_1_MODE 2	# Onboard
			param set-default SER_TEL2_BAUD 921600 # VIO data
		fi
	fi

	# User is setting defaults, so let's do it!
	if [ $AUTOCNF = yes ]
	then
		echo "V106 - Auto Configuring TELEM2 on /dev/ttyS4 at 921600 in Normal Mode"
		param set-default MAV_1_CONFIG 102 # TELEM2
		param set-default MAV_1_MODE 2	# Onboard
		param set-default SER_TEL2_BAUD 921600 # VIO data
	fi
fi

#
# VOXL-Flight configuration
#
if ver hwtypecmp V110
then
	echo "Configuring VOXL-Flight - V110"

	#
	# TELEM2 port is physically routed in the PCB, thus not configurable.
	# The following will detect a fresh install, or if the user has changed the setting and
	# revert to the VOXL-Flight defaults.  This does allow the user to change the mode and
	# baud rates and mode if they choose to do so, although VOXL is expecting what is set below
	#
	if [ $AUTOCNF = no ]
	then
		if ! param compare MAV_1_CONFIG 102
		then
			echo "V110 - Defualt configuration TELEM2 on /dev/ttyS4 at 921600 in Normal Mode"
			param set-default MAV_1_CONFIG 102 # TELEM2
			param set-default MAV_1_MODE 2	# Onboard
			param set-default SER_TEL2_BAUD 921600
		fi
	fi

	# User is setting defaults, so let's do it!
	if [ $AUTOCNF = yes ]
	then
		echo "V110 - Auto Configuring TELEM2 on /dev/ttyS4 at 921600 in Normal Mode"
		param set-default MAV_1_CONFIG 102 # TELEM2
		param set-default MAV_1_MODE 2	# Onboard
		param set-default SER_TEL2_BAUD 921600
	fi
fi


safety_button start