yemai/bizhang_-obav
1
0
Fork 0
mirror of https://gitee.com/xiaohuolufeihua/bizhang_-obav.git synced 2026-05-22 01:12:31 +00:00
Code Issues Packages Projects Releases Wiki Activity
34,645 Commits 2 Branches 0 Tags
cd7713eba246b003555f94cbce357cb69c51c140
Commit Graph

37 Commits

Author SHA1 Message Date
Daniel Agar
cd7713eba2 boards: delete unused variants 2021-02-22 20:08:36 -05:00
Daniel Agar
414f9f81d9 move fake GPS to standalone module 2021-02-20 14:13:36 -05:00
Daniel Agar
ab0d0fd0be uORB move to PX4 platform layer 2021-02-17 11:25:56 -05:00
Daniel Agar
44df0fb7a2 Analog Devices ADIS16448 rewrite 
- new IMU driver structure with state machine (no sleeps in bus thread)
 - verify all configured registers and trigger reset on failure
 - detect if DIO1 or DIO2 are actually connected for data ready interrupt usage
 - don't use CRC-16 on burst transfers except for verified lots
 2021-02-16 10:29:07 +01:00
Daniel Agar
fb2a199621 delete unmaintaned mkblctrl driver 2021-02-14 10:38:15 +01:00
Daniel Agar
a257120e8d boards: use new param default mechanism 2021-02-12 08:27:47 -05:00
Daniel Agar
8f0918a16b boards: remove unused linker __param section 2021-02-08 23:22:48 -05:00
Daniel Agar
a2442ffb48 board: enable UAVCAN sensors by default on F7/H7 2021-02-02 09:01:12 +01:00
Daniel Agar
f0d1f1d679 boards: disable BDMA on STM32H7 for now 2021-01-28 21:16:23 +01:00
David Sidrane
455f762516 px4_fmu-v6x:Support RC03 HW 2021-01-25 09:18:24 +01:00
Daniel Agar
1ec10bfcc6 boards: disable CONFIG_ARMV7M_LAZYFPU again (#16573) 
- this was causing hard faults on the CUAV Nora and possibly other boards, disabling everywhere until we fully understand the root cause
 2021-01-17 22:40:21 -05:00
Beat Küng
26e8c231b0 v5x,v6x: move mtd_caldata after mtd_id partition 
to avoid losing factory calibration params on existing setups
 2021-01-15 10:57:20 -05:00
Beat Küng
9f5dee2ecf v5x/v6x: update IMU sensors (remove ISM330DLC) 2021-01-12 09:55:59 -05:00
Daniel Agar
cb74cb8692 boards: enable CONFIG_ARMV7M_LAZYFPU everywhere 2021-01-12 09:04:38 +01:00
Daniel Agar
763c3b8fda boards: start enabling multi-EKF by default on F7/H7 2021-01-10 17:56:34 +01:00
Matthias Grob
7545249215 Add flight_mode_manager to all targets with mc_pos_control 2020-12-30 10:25:08 -05:00
David Sidrane
22bc176885 Added mft for queries 2020-12-02 20:40:23 -05:00
David Sidrane
44ffc855dc px4_fmu-v6x: Use px4_platform_configure 2020-12-02 20:40:23 -05:00
David Sidrane
ff87bc0fda fmu-v6x:Bootloader init NULL console 2020-10-28 14:25:25 -04:00
Daniel Agar
233949a377 NuttX upgrade to 10.0.0+ defconfig changes 2020-10-28 14:25:25 -04:00
Beat Küng
274ccaf57c system: include shutdown lock to BOARD_INDICATE_ARMED_STATE 
BOARD_INDICATE_ARMED_STATE was only set during arming, so an external
component might have reset the board during param save, leading to param
loss.

This extends the API to trigger the arming state also while the shutdown
lock is taken.
 2020-10-09 08:23:47 +02:00
David Sidrane
529d816a39 px4_fmu-v6x:Support ETM Hardware Trace 2020-09-28 10:59:39 -04:00
Tanja Baumann
b5ebdb8e41 add system command to get and set system time 
* add system_time command for all boards
 2020-09-26 13:09:01 -04:00
David Sidrane
c7642288db px4_fmu-v6x: Updates for NuttX 9.1.0+ External schedule_note 2020-09-16 21:32:04 -04:00
David Sidrane
1a51a84130 px4_fmu-v6x: Updates for NuttX 9.1.0+ External schedule_note 2020-09-16 21:32:04 -04:00
David Sidrane
72c681134d px4_fmu-v6x:Add support for DMA on SPI6 2020-09-16 21:32:04 -04:00
David Sidrane
f870594f1d px4_fmu-v6x Updates for NuttX 9.1.0- 
px4_fmu-v6x: defconfig MMCSD enable multiblock
 2020-09-16 21:32:04 -04:00
SalimTerryLi
c037dbef21 Rename and move src/drivers/adc to src/drivers/adc/board_adc 2020-09-07 23:09:20 -04:00
Daniel Agar
2c3441aa90 boards: reduce CONFIG_NFILE_DESCRIPTORS 15 -> 12 
- reduced now that calibration uses uORB::Subscription
 - can likely be reduced further (perhaps < 8) with additional testing
 2020-08-21 10:12:13 -04:00
David Sidrane
22a7bf6ec7 px4_fmu-v6x Fix BOARD_TYPE 2020-08-14 11:23:16 -04:00
Daniel Agar
e3d31a881e boards: NuttX disable posix message queues 2020-07-17 17:00:21 -04:00
David Sidrane
28a695dce4 px4_fmu-v6x:imu/bmi088->imu/bosch/bmi088 2020-06-19 19:13:20 -04:00
Daniel Agar
6f6efd60b7 boards: centralize optional external I2C sensor start 
- configured with new parameter SENS_EXT_I2C_PRB
 2020-06-10 09:04:13 -04:00
David Sidrane
82b87adfb3 px4_fmu-v6x:default phy is LAN8742 2020-06-09 08:14:22 +02:00
Daniel Agar
5e7d2e830d boards: delete old board.h boilerplate 2020-06-08 19:10:33 -04:00
David Sidrane
73bb18a053 px4_fmu-v6x: Limit Slew rate So IMU works with DMA 
The defualt in NuttX is OSPEED of 50Mhz. This is realy a slew
   rate control. At the default high slew rate the overshoot was
   .7 Volts. On a ICM20649 this was causing the device to output
   garbage. All 0s

   N.B. A passive scope or Logic analyser's probes load will mask
   the failure. Useed a FET probe to verify the issue.
 2020-06-02 13:02:51 -04:00
David Sidrane
5d90c31632 Added PX4 FmuV6X 2020-06-02 13:02:51 -04:00