- sitl_gazebo in PX4/Firmware (c3884b5bc1): 402897d225
- sitl_gazebo current upstream: f10ccb7ec3
- Changes: 402897d225...f10ccb7ec3
f10ccb7 2021-05-17 grahamjamesaddis - Fix non unique name warning in tailsitter.sdf.jinja (#756)
05b8625 2021-05-13 Andrew Voznytsa - Fix gstreamer timestamps; Use push mode all the way; Avoid duplicated frame encoding; Cleanup a bit there and here
9ec04cc 2021-05-16 Graham James Addis - Tidy rotor colours Grey/Blue.
493c5dc 2021-05-16 Graham James Addis - Minimal conversion to jinja format.
- ecl in PX4/Firmware (4668ea5c32075aca28fd813881a349f765ad8d2a): 29243ac5cb
- ecl current upstream: 85f5a935fe
- Changes: 29243ac5cb...85f5a935fe
85f5a93 2021-05-11 bresch - [AUTO COMMIT] update change indication
f7c687e 2021-05-11 bresch - GNSS yaw unit test: test fallback to non yaw aiding mode
a4fe2b1 2021-05-11 bresch - yaw_align: let the mag control logic do the alignement and resets
2cc0230 2021-05-11 bresch - mag control: select mag mode before doing the reset
fe943cf 2021-05-11 bresch - mag reset: force align in MC custom mode (aka. indoor mode)
cadcc58 2021-05-11 bresch - mag reset: do not stop the fusion from inside the reset function
6248646 2021-05-11 bresch - EV yaw: move EV yaw reset out of resetMagHeading function
48722a2 2021-05-07 bresch - control: inhibit EV yaw from restarting when GPS aid wants to start
a685987 2021-05-07 bresch - GNSS yaw: unset yaw_align if fusion stops before takeoff
7ee6970 2021-05-04 bresch - GNSS yaw: add test case when measurement jumps
7a11871 2021-05-04 bresch - GNSS yaw tests: adjust timing
51197a5 2021-05-03 bresch - GNSS yaw selection logic refactor
e.g.:
WARN [mavlink] stream ADSB_VEHICLE not found
WARN [mavlink] stream GIMBAL_DEVICE_ATTITUDE_STATUS not found
WARN [mavlink] stream GIMBAL_MANAGER_STATUS not found
WARN [mavlink] stream GIMBAL_DEVICE_SET_ATTITUDE not found
WARN [mavlink] stream GPS2_RAW not found
WARN [mavlink] stream UTM_GLOBAL_POSITION not found
ERROR [mavlink] configure_streams_to_default() failed
This avoids incremental build errors when switching between branches with
a different set of airframes.
E.g:
Aborting due to missing @type tag in file: 'Firmware/build/px4_fmu-v5_default/etc/init.d/airframes/13030_generic_vtol_quad_tiltrotor'
- update clean to recurse all build directories and use build system clean
- git clean is used to remove submodule generated build artifacts that
are left in the source tree
- distclean now discards all build directories and any gitignored
filess that were generated in source directories (but not top level)
The calibration is not found in HITL mode. Therefore, I suggest to
ignore this step and assume the calibration is fine.
This mostly fixes the preflight check indicator in QGC, arming was (for
some reason?) already possible.
[BACKPORT] binnfmt:Fix return before close ELF fd
stm32h7: serial: use dma tx semaphore as resource holder
[BACKPORT] stm32h7:Serial Add RX and TX DMA
[BACKPORT] drivers/serial: fix Rx interrupt enable for cdcacm
[BACKPORT] stm32h7:Allow for reuse of the OTG_ID GPIO
[BACKPORT] stm32f7:Allow for reuse of the OTG_ID GPIO
