David Sidrane
05bdef867d
Track NuttX syslog change
2021-06-16 17:07:47 +02:00
David Sidrane
62fd132047
boards:Use inttypes
...
nxp_ucans32k146:Fix constant
spracing_h7extreme:Use inttypes
2021-06-16 17:07:47 +02:00
echoG
6bc09138c1
Adding BatMon smart battery as a module and refactoring SMBUS based SBS 1.1 spec to a library
2021-06-09 12:17:45 -04:00
David Sidrane
32e92ba817
Revert:Pull downs - bad levels cause motor spins
2021-06-01 15:18:47 -04:00
Daniel Agar
c3884b5bc1
fake_imu (formally fake_gyro) updates for testing gyro filtering
...
- fake_imu now publishes sine sweeps over 10 seconds
- accel is also published so that fake IMU can be selected when the only option
2021-05-17 20:26:25 -04:00
David Sidrane
3779ff3690
holybro_pix32v5: Disable OTG_ID_GPIO
2021-05-05 20:48:06 +02:00
David Sidrane
9c761d9ae5
holybro_pix32v5: Initalize PWM as input with Pull Downs
2021-05-05 20:48:06 +02:00
Daniel Agar
58b40fbbb9
boards: move testing to dedicated test variants
2021-04-14 09:21:31 +02:00
Daniel Agar
ad934b4911
icm20948 i2c passthrough driver for ak09916 magnetometer (Here+ GPS/compass)
...
- include icm20948 on most boards by default
- create more test variants for default boards near flash limit (cuav_nora_test, cuav_x7pro_test, holybro_durandal-v1_test)
2021-04-04 21:18:16 -04:00
Daniel Agar
6874e9fba0
boards: NuttX disable all NSH memory debug commands (mb, mh, mw) by default
...
- closes https://github.com/PX4/PX4-Autopilot/issues/17062
2021-03-30 09:23:43 -04:00
Daniel Agar
631d1647d3
boards: minimize unnecessary differences in default variants
2021-03-28 14:46:47 -04:00
Daniel Agar
4b99bd2077
boards: remove optional external ADIS IMUs to save flash
2021-03-15 13:37:24 -04:00
Daniel Agar
2257c3767e
simple gyro auto calibration module
2021-03-15 09:46:47 +01:00
Daniel Agar
f8eaa6e46b
ROMFS handle bl_update generically
...
- include all available legacy bootloaders
2021-03-11 00:38:18 +01:00
Daniel Agar
4d288512b5
add board architecture specific init defaults
2021-03-09 19:59:41 +01:00
Daniel Agar
19de1e57e3
gyro_fft promote to modules and include on all boards
2021-03-05 10:56:54 -05:00
Beat Küng
7e33d03470
drivers: remove tap_esc
...
- it's not used anymore
- it would need a refactoring to use mixer_module
2021-02-25 09:28:37 -05:00
Daniel Agar
11ad41f7cb
delete old imu/mpu6000 driver
2021-02-23 15:58:36 -05:00
Daniel Agar
414f9f81d9
move fake GPS to standalone module
2021-02-20 14:13:36 -05:00
Daniel Agar
ab0d0fd0be
uORB move to PX4 platform layer
2021-02-17 11:25:56 -05:00
Daniel Agar
44df0fb7a2
Analog Devices ADIS16448 rewrite
...
- new IMU driver structure with state machine (no sleeps in bus thread)
- verify all configured registers and trigger reset on failure
- detect if DIO1 or DIO2 are actually connected for data ready interrupt usage
- don't use CRC-16 on burst transfers except for verified lots
2021-02-16 10:29:07 +01:00
Daniel Agar
fb2a199621
delete unmaintaned mkblctrl driver
2021-02-14 10:38:15 +01:00
Daniel Agar
a257120e8d
boards: use new param default mechanism
2021-02-12 08:27:47 -05:00
Daniel Agar
8f0918a16b
boards: remove unused linker __param section
2021-02-08 23:22:48 -05:00
Daniel Agar
a2442ffb48
board: enable UAVCAN sensors by default on F7/H7
2021-02-02 09:01:12 +01:00
Daniel Agar
1ec10bfcc6
boards: disable CONFIG_ARMV7M_LAZYFPU again ( #16573 )
...
- this was causing hard faults on the CUAV Nora and possibly other boards, disabling everywhere until we fully understand the root cause
2021-01-17 22:40:21 -05:00
Daniel Agar
cb74cb8692
boards: enable CONFIG_ARMV7M_LAZYFPU everywhere
2021-01-12 09:04:38 +01:00
Daniel Agar
763c3b8fda
boards: start enabling multi-EKF by default on F7/H7
2021-01-10 17:56:34 +01:00
Matthias Grob
7545249215
Add flight_mode_manager to all targets with mc_pos_control
2020-12-30 10:25:08 -05:00
David Sidrane
22bc176885
Added mft for queries
2020-12-02 20:40:23 -05:00
David Sidrane
a2a8d2fcf2
holybro_pix32v5: Use px4_platform_configure
2020-12-02 20:40:23 -05:00
Daniel Agar
c60743b306
boards: NuttX increase file name max 32 -> 40
2020-11-08 12:51:59 -05:00
Daniel Agar
233949a377
NuttX upgrade to 10.0.0+ defconfig changes
2020-10-28 14:25:25 -04:00
Beat Küng
274ccaf57c
system: include shutdown lock to BOARD_INDICATE_ARMED_STATE
...
BOARD_INDICATE_ARMED_STATE was only set during arming, so an external
component might have reset the board during param save, leading to param
loss.
This extends the API to trigger the arming state also while the shutdown
lock is taken.
2020-10-09 08:23:47 +02:00
Tanja Baumann
b5ebdb8e41
add system command to get and set system time
...
* add system_time command for all boards
2020-09-26 13:09:01 -04:00
David Sidrane
15c8a26a21
holybro_pix32v5: Updates for NuttX 9.1.0+ External schedule_note
2020-09-16 21:32:04 -04:00
David Sidrane
f9adf861dc
spracing_h7extreme Updates for NuttX 9.1.0-
2020-09-16 21:32:04 -04:00
David Sidrane
c2419e7f3d
holybro_pix32v5: Updates for NuttX 9.1.0-
2020-09-16 21:32:04 -04:00
SalimTerryLi
c037dbef21
Rename and move src/drivers/adc to src/drivers/adc/board_adc
2020-09-07 23:09:20 -04:00
Beat Küng
787f9c1213
i2c: use board-specific bus numbering for '-X -b <bus>' CLI
...
As boards don't have their external buses labeled consistently, it was not
useful to use an abstraction.
2020-09-03 15:32:35 -04:00
Daniel Agar
7569722821
iSentek IST8310 magnetometer rewrite
...
- simple state machine to reset, configure, etc
- checked register mechanism (sensor will reset itself on configuration error)
- configured in 16 bit mode (1320 LSB/Gauss instead of 330 LSB/Gauss)
- adjusted orientation handling in driver to match datasheet as closely as possible
- in many external compass units the rotation was wrong and very difficult to actual determine how to set correctly
2020-09-02 13:14:45 -04:00
Daniel Agar
2c3441aa90
boards: reduce CONFIG_NFILE_DESCRIPTORS 15 -> 12
...
- reduced now that calibration uses uORB::Subscription
- can likely be reduced further (perhaps < 8) with additional testing
2020-08-21 10:12:13 -04:00
Daniel Agar
e16c8fa345
boards: add new Holybro Pix32v5
2020-08-09 11:48:38 -04:00