support multi port api for device

common/usb_dc.h

@@ -16,13 +16,13 @@ extern "C" {
  * @brief init device controller registers.
  * @return On success will return 0, and others indicate fail.
  */
-int usb_dc_init(void);
+int usb_dc_init(uint8_t busid);
 
 /**
  * @brief deinit device controller registers.
  * @return On success will return 0, and others indicate fail.
  */
-int usb_dc_deinit(void);
+int usb_dc_deinit(uint8_t busid);
 
 /**
  * @brief Set USB device address
@@ -31,7 +31,7 @@ int usb_dc_deinit(void);
  *
  * @return On success will return 0, and others indicate fail.
  */
-int usbd_set_address(const uint8_t addr);
+int usbd_set_address(uint8_t busid, const uint8_t addr);
 
 /**
  * @brief Get USB device speed
@@ -40,7 +40,7 @@ int usbd_set_address(const uint8_t addr);
  *
  * @return port speed, USB_SPEED_LOW or USB_SPEED_FULL or USB_SPEED_HIGH
  */
-uint8_t usbd_get_port_speed(const uint8_t port);
+uint8_t usbd_get_port_speed(uint8_t busid, const uint8_t port);
 
 /**
  * @brief configure and enable endpoint.
@@ -49,7 +49,7 @@ uint8_t usbd_get_port_speed(const uint8_t port);
  *
  * @return On success will return 0, and others indicate fail.
  */
-int usbd_ep_open(const struct usb_endpoint_descriptor *ep);
+int usbd_ep_open(uint8_t busid, const struct usb_endpoint_descriptor *ep);
 
 /**
  * @brief Disable the selected endpoint
@@ -58,7 +58,7 @@ int usbd_ep_open(const struct usb_endpoint_descriptor *ep);
  *
  * @return On success will return 0, and others indicate fail.
  */
-int usbd_ep_close(const uint8_t ep);
+int usbd_ep_close(uint8_t busid, const uint8_t ep);
 
 /**
  * @brief Set stall condition for the selected endpoint
@@ -68,7 +68,7 @@ int usbd_ep_close(const uint8_t ep);
  *
  * @return On success will return 0, and others indicate fail.
  */
-int usbd_ep_set_stall(const uint8_t ep);
+int usbd_ep_set_stall(uint8_t busid, const uint8_t ep);
 
 /**
  * @brief Clear stall condition for the selected endpoint
@@ -78,7 +78,7 @@ int usbd_ep_set_stall(const uint8_t ep);
  *
  * @return On success will return 0, and others indicate fail.
  */
-int usbd_ep_clear_stall(const uint8_t ep);
+int usbd_ep_clear_stall(uint8_t busid, const uint8_t ep);
 
 /**
  * @brief Check if the selected endpoint is stalled
@@ -89,7 +89,7 @@ int usbd_ep_clear_stall(const uint8_t ep);
  *
  * @return On success will return 0, and others indicate fail.
  */
-int usbd_ep_is_stalled(const uint8_t ep, uint8_t *stalled);
+int usbd_ep_is_stalled(uint8_t busid, const uint8_t ep, uint8_t *stalled);
 
 /**
  * @brief Setup in ep transfer setting and start transfer.
@@ -108,7 +108,7 @@ int usbd_ep_is_stalled(const uint8_t ep, uint8_t *stalled);
  *                       be zero for a zero length status packet.
  * @return 0 on success, negative errno code on fail.
  */
-int usbd_ep_start_write(const uint8_t ep, const uint8_t *data, uint32_t data_len);
+int usbd_ep_start_write(uint8_t busid, const uint8_t ep, const uint8_t *data, uint32_t data_len);
 
 /**
  * @brief Setup out ep transfer setting and start transfer.
@@ -127,40 +127,40 @@ int usbd_ep_start_write(const uint8_t ep, const uint8_t *data, uint32_t data_len
  *
  * @return 0 on success, negative errno code on fail.
  */
-int usbd_ep_start_read(const uint8_t ep, uint8_t *data, uint32_t data_len);
+int usbd_ep_start_read(uint8_t busid, const uint8_t ep, uint8_t *data, uint32_t data_len);
 
 /* usb dcd irq callback */
 
 /**
  * @brief Usb connect irq callback.
  */
-void usbd_event_connect_handler(void);
+void usbd_event_connect_handler(uint8_t busid);
 
 /**
  * @brief Usb disconnect irq callback.
  */
-void usbd_event_disconnect_handler(void);
+void usbd_event_disconnect_handler(uint8_t busid);
 
 /**
  * @brief Usb resume irq callback.
  */
-void usbd_event_resume_handler(void);
+void usbd_event_resume_handler(uint8_t busid);
 
 /**
  * @brief Usb suspend irq callback.
  */
-void usbd_event_suspend_handler(void);
+void usbd_event_suspend_handler(uint8_t busid);
 
 /**
  * @brief Usb reset irq callback.
  */
-void usbd_event_reset_handler(void);
+void usbd_event_reset_handler(uint8_t busid);
 
 /**
  * @brief Usb setup packet recv irq callback.
  * @param[in]  psetup  setup packet.
  */
-void usbd_event_ep0_setup_complete_handler(uint8_t *psetup);
+void usbd_event_ep0_setup_complete_handler(uint8_t busid, uint8_t *psetup);
 
 /**
  * @brief In ep transfer complete irq callback.
@@ -168,7 +168,7 @@ void usbd_event_ep0_setup_complete_handler(uint8_t *psetup);
  *                       listed in the device configuration table
  * @param[in]  nbytes    How many nbytes have transferred.
  */
-void usbd_event_ep_in_complete_handler(uint8_t ep, uint32_t nbytes);
+void usbd_event_ep_in_complete_handler(uint8_t busid, uint8_t ep, uint32_t nbytes);
 
 /**
  * @brief Out ep transfer complete irq callback.
@@ -176,7 +176,7 @@ void usbd_event_ep_in_complete_handler(uint8_t ep, uint32_t nbytes);
  *                       listed in the device configuration table
  * @param[in]  nbytes    How many nbytes have transferred.
  */
-void usbd_event_ep_out_complete_handler(uint8_t ep, uint32_t nbytes);
+void usbd_event_ep_out_complete_handler(uint8_t busid, uint8_t ep, uint32_t nbytes);
 
 #ifdef __cplusplus
 }