update ehci driver

common/usb_hc.h

@@ -78,7 +78,7 @@ int usbh_reset_port(const uint8_t port);
  * @brief get roothub port speed
  *
  * @param port port index
- * @return return 0 means USB_SPEED_LOW, 1 means USB_SPEED_FULL and 2 means USB_SPEED_HIGH.
+ * @return return 1 means USB_SPEED_LOW, 2 means USB_SPEED_FULL and 3 means USB_SPEED_HIGH.
  */
 uint8_t usbh_get_port_speed(const uint8_t port);
 

port/ehci/usb_ehci.c

@@ -2192,10 +2192,11 @@ int usb_hc_init(void)
     usb_ehci_putreg(regval, &HCOR->usbcmd);
 
     /* Route all ports to this host controller by setting the CONFIG flag. */
-    // regval = usb_ehci_getreg(&HCOR->configflag);
+#ifdef CONFIG_USB_EHCI_CONFIGFLAG
-    // regval |= EHCI_CONFIGFLAG;
+    regval = usb_ehci_getreg(&HCOR->configflag);
-    // usb_ehci_putreg(regval, &HCOR->configflag);
+    regval |= EHCI_CONFIGFLAG;
-
+    usb_ehci_putreg(regval, &HCOR->configflag);
+#endif
     /* Wait for the EHCI to run (i.e., no longer report halted) */
     ret = usb_ehci_wait_usbsts(EHCI_USBSTS_HALTED, 0, 100 * 1000);
     if (ret < 0) {
@@ -2212,6 +2213,52 @@ int usb_hc_init(void)
     return ret;
 }
 
+int usbh_reset_port(const uint8_t port)
+{
+    uint32_t timeout = 0;
+    uint32_t regval;
+    regval = usb_ehci_getreg(&HCOR->portsc[port - 1]);
+    regval &= ~EHCI_PORTSC_PE;
+    regval |= EHCI_PORTSC_RESET;
+    usb_ehci_putreg(regval, &HCOR->portsc[port - 1]);
+
+    usb_osal_msleep(55);
+
+    regval = usb_ehci_getreg(&HCOR->portsc[port - 1]);
+    regval &= ~EHCI_PORTSC_RESET;
+    usb_ehci_putreg(regval, &HCOR->portsc[port - 1]);
+
+    /* Wait for the port reset to complete
+    *
+    * Paragraph 2.3.9:
+    *
+    *  "Note that when software writes a zero to this bit there may be a
+    *   delay before the bit status changes to a zero. The bit status will
+    *   not read as a zero until after the reset has completed. If the port
+    *   is in high-speed mode after reset is complete, the host controller
+    *   will automatically enable this port (e.g. set the Port Enable bit
+    *   to a one). A host controller must terminate the reset and stabilize
+    *   the state of the port within 2 milliseconds of software transitioning
+    *   this bit from a one to a zero ..."
+    */
+
+    while ((usb_ehci_getreg(&HCOR->portsc[port - 1]) & EHCI_PORTSC_RESET) != 0) {
+        usb_osal_msleep(1);
+        timeout++;
+        if (timeout > 100) {
+            return -ETIMEDOUT;
+        }
+    }
+
+    return 0;
+}
+
+__WEAK uint8_t usbh_get_port_speed(const uint8_t port)
+{
+    /* Defined by individual manufacturers */
+    return 0;
+}
+
 int usbh_ep0_reconfigure(usbh_epinfo_t ep, uint8_t dev_addr, uint8_t ep_mps, uint8_t speed)
 {
     struct usb_ehci_epinfo_s *epinfo;

port/ehci/usb_ehci.h

@@ -872,7 +872,9 @@ struct ehci_hcor_s
   uint32_t ctrldssegment;    /* 0x10: 4G Segment Selector */
   uint32_t periodiclistbase; /* 0x14: Frame List Base Address */
   uint32_t asynclistaddr;    /* 0x18: Next Asynchronous List Address */
-  // uint32_t reserved[9];
+#ifdef CONFIG_USB_ECHI_HCOR_RESERVED
+  uint32_t reserved[9];
+#endif
   uint32_t configflag;       /* 0x40: Configured Flag Register */
   uint32_t portsc[15];       /* 0x44: Port Status/Control */
 };